Parking Areas
Reliable emergency lighting for underground and multi-level parking facilities, ensuring safety in low-light conditions.
The SINO F6 PIR Motion Sensor offers smart, energy-efficient lighting control with passive infrared detection across a 360° range, adjustable up to 6 meters. Ideal for both residential and commercial spaces, it activates lights only when needed, thanks to customizable time delay and LUX settings.
Distinguishing between day and night, it’s perfect for hallways, stairwells, garages, and offices. Fully passive with zero microwave emission, the SINO F6 enhances safety, convenience, and energy savings, making it a reliable, no-emission choice for continuous residential and commercial lighting automation.
Voltage |
110–240V AC |
Power Frequency |
50/60 Hz |
Sensor Type |
Passive Infrared (PIR) |
Detection Range |
360° |
Detection Distance |
6m max (at <24°C) |
Moving Speed |
0.6–1.5 m/s |
Ambient Light |
<3–2000 LUX (adj.) |
Max Load |
2000W (220–240V)1000W (110–130V) 1000W (220–240V)500W (110–130V) |
Time Delay |
10 sec – 15 min |
Install Height |
2.2–4m (ideal 3m) |
Working Temp |
–20°C to +40°C |
Working Humidity |
<93% RH |
SENS refers to the diameter of the detection zone, which is roughly circular, produced on the ground when the sensor is mounted at a height of 2.5 to 6 meters. Turn the SENS control fully counterclockwise to select the minimum SENS (approximately 2 meters in diameter) and fully clockwise to select the maximum SENS (approximately 16 meters in diameter). Adjust according to location and site requirements
The light can be set to stay on for any period of time between approximately 10 seconds (turn fully counterclockwise) and a maximum of 12 minutes (turn fully clockwise). Any movement detected before this time elapses will restart the timer. It is recommended to select the shortest duration necessary for your needs.
The chosen light response threshold can be adjusted from approximately 3 to 2000 lux. Turn the knob fully counterclockwise to select dusk-to-dawn operation at about 3 lux, and fully clockwise for continuous daylight operation. The knob must be turned fully clockwise when adjusting the detection zone and performing the walk test in daylight. Afterward, adjust the setting according to site requirements. Allow sufficient time for adjusting the detection zone and for performing the walk test.
SINO F6 is a PIR Motion Sensor that uses passive infrared energy radiated by the human body. No microwave emission — completely safe for continuous use.
Discover the simple yet effective way NANO 16 transforms your space
Emits 5.8GHz microwaves with <0.2mW power, ensuring precise detection.
Detects movement (0.6–1.5m/s) within 360° range, adjustable 2–16m.
Activates lights (≤800W incandescent / 300W LED) with 10s–12min delay.
A microwave motion sensor works by emitting high-frequency waves and detecting changes in the reflected signal. When motion occurs within the microwave sensor range, the reflection shifts, triggering a response. Unlike passive sensors, microwave sensors actively scan their surroundings, making them ideal for detecting subtle movement, even through walls or glass.
Advanced passive infrared technology for superior motion detection
Advanced 50/60 GHz technology for reliable motion detection through walls and doors
Comprehensive coverage for peace of mind
Smart power management reduces consumption
Designed for indoor environments
Yes, adjustable <3–2000 LUX
Delay Time
Detection Range
Install Height
Discover how the Nano F16 Microwave Motion Sensor automates lighting across common circulation areas with reliable detection and energy-efficient operation.
Hallways, stairwells, bathrooms, garages. Hands-free lighting for daily convenience.
Offices, meeting rooms, retail areas. Automate lighting for energy savings.
Warehouses, loading bays. IP44 rated for dusty, lightly damp environments.
Covered porches, carports. Not for direct rain exposure
Reliable emergency lighting for underground and multi-level parking facilities, ensuring safety in low-light conditions.
Experience intuitive lighting control with Nano F16’s advanced sensing modes and adjustable settings.
In Daylight mode, Nano F16 only turns lights ON when both conditions are met: motion is detected and the ambient light level is below the set lux threshold. This prevents lights from switching on unnecessarily in naturally bright spaces such as corridors with windows or staircases with skylights.
When there is enough natural light, the sensor keeps the light OFF even if motion is detected.
When the ambient light falls below the set level and the sensor detects movement, the light switches ON automatically.
Once motion stops, the light remains ON for the selected hold time and then switches OFF automatically.
In No Daylight mode, Nano F16 ignores the ambient light level and responds purely to motion. This mode is ideal for consistently dim or enclosed areas such as basement parking, internal corridors, and underpasses where lights must always come on whenever movement is detected.
As soon as a person or vehicle enters the detection zone, the sensor switches the light ON to full brightness.
As long as motion continues, the light stays ON, ensuring a safe and comfortable environment.
After the last detection and expiry of the configured hold time, the light turns OFF automatically.
Nano F16 can differentiate between day and night using its built-in light sensing. It automatically adjusts operation based on ambient lux levels, ensuring lights are used only when they’re actually needed.
Set the detection range to suit the space. Nano F16 allows fine adjustment of sensitivity so that motion is detected only within the desired area, helping avoid false triggers from adjacent zones.
Smart re-triggering means the timer resets whenever new motion is detected. Lights remain ON continuously while people are present, providing uninterrupted illumination during peak activity.
Choose how long the lights stay ON after the last detection. The adjustable hold time lets you match sensor behaviour to the application, from quick shut-off for short passages to longer delays for high-traffic areas.
Find answers to common questions about Nano F16
SINO F6 uses PIR (Passive Infrared) technology, detecting changes in infrared radiation naturally emitted by the human body. It’s entirely passive and emits no radiation of any kind, making it completely safe for continuous residential and commercial use.
SINO F6 uses PIR technology to detect movement across its Fresnel lens zones, so it needs crossing motion to trigger — it won’t detect a person sitting still. SINO PRO, by contrast, uses microwave radar to detect breathing, keeping lights on even when you’re stationary. If you need lighting to stay on for someone sitting still at a desk, SINO PRO is the better fit; for general movement-based automation, SINO F6 is ideal.
Mount it centrally on the ceiling at a height of 2.2–4m (3m is ideal), with a clear, unobstructed 360° view. Avoid mirrors, glass, or highly reflective surfaces, heat sources like vents, AC units, or halogen lamps, and areas with draughts from curtains, tall plants, or fans, as these can affect detection.
This is normal. SINO F6 has a 30-second warm-up period after every power-on, during which it won’t detect motion. Once warm-up is complete, it will begin functioning normally.
SINO F6 is IP44 rated, suitable for covered outdoor areas like porches and carports, but it’s not designed for direct rain exposure.
© Sensinova India 2026. All rights reserved.
